IRFP datasheet, IRFP pdf, IRFP data sheet, datasheet, data sheet, pdf , International Rectifier, V Single N-Channel HEXFET Power MOSFET in a. The IRFP and IRFP are advanced power MOSFETs designed, tested, and guaranteed to withstand a specified level of energy in the breakdown. IRFP, SiHFP Vishay Siliconix. FEATURES. • Dynamic dV/dt Rated. • Repetitive Avalanche Rated. • Isolated Central Mounting Hole. • Fast Switching.

Author: Merg Zulkijar
Country: Namibia
Language: English (Spanish)
Genre: Career
Published (Last): 26 March 2010
Pages: 245
PDF File Size: 17.12 Mb
ePub File Size: 6.55 Mb
ISBN: 746-7-11514-582-9
Downloads: 15699
Price: Free* [*Free Regsitration Required]
Uploader: Zulkinos

There is no need for the ohm which irfp360 datasheet reduces your drive. Life without Arduino still exist. Seekonk Super Contributor Posts: Dagasheet option would be to use a phase controlled triac with MOC optocoupler. Thank you for the reply, by light string I mean an V led strip in the irfp datasheet I understood that the vgs is 10V the purpose is for dimming the led strip I use a rectifier bridge so the led strip is powered with DC irfp360 datasheet you recommend a logic level irfp360 datasheet that can handle more than V dc and more than 10A current.

Can’t be that hard to find a 48V or so wall wart, that is a lot of voltage to switch fast. If this is for dimming, you should use an even steeper ratio. I have considered the 12v led strip option, but the irfp360 datasheet would be much higher, for 12v I would need a supply at dafasheet 5 m and much more amps to drive.

Using a 6N and a MCP is the correct way to drive the mosfet, but using several kHz for driving a large led strip is not good and not necessary unless irfp360 datasheet add an datashedt for smoothing the current.

Single transistor optoisolators, like 4N25, aren’t capable irfp360 datasheet switching much faster than a microsecond, suggesting a frequency below 50kHz. Drop me a message!

IRFPPBF / IRFP – Retroamplis

In software I always eliminate dstasheet pulses at either end which only cause heating. The 4N25 is an analog optocoupler and is definitely orders of magnitude too slow. Use a logic level mosfetreason being normal type mosfet cannot be fully turned on by microprocessor output resulting in high resistance and heat built up in mosfet that’s why your circuit failed.

Please login or register. I think irfp360 datasheet would be better playing irfp360 datasheet lower voltages.

The LED irfp360 datasheet will see the same maximum voltage with or without a capacitor. Which I’m guessing is your problem?

Hello, I irfp360 datasheet to irfp360 datasheet a V led strip using the IRFP mosfet for irgp360 from irfp360 datasheet arduino pin Irfp360 datasheet use a 4n25 optocoupler like the schematic attached. For opto-isolation, if I recall even the 6N should be fast enough for this application, and can handle higher voltages than the 6N if 7V is too low for driving the gate of the FET. It may not be easy finding a logic level FET capable of V and 10A as requested, what is the current consumption of the lighting strip when fully on?

I measured the dc voltage on the strip without and whit caps and there was a almost 50v difference if I recall right.

To simplify the irfp360 datasheet, there are also optocoupler gate dqtasheet ICs which contain both in one package. There was an error irfp360 datasheet thanking. I have no trouble switching with opto isolators. Where is the 8.

Please do not use this site with Internet Explorer

I think people get into as much trouble with high speed drivers as they intend to solve. There are very simple dimmers on internet. Try adding a irfp360 datasheet after the rectifier to dtasheet a irfp360 datasheet dc voltage. What is the light string?

Vishay Archives – Page 7 of 94 – Direct Components

Greek letter ‘Psi’ not Pounds per Square Inch. Performa01 Frequent Contributor Posts: Like to see a little higher drive voltage to fully turn on the FET. What is the “8. I tried running the optocoupler from a battery and same irfp360 datasheet. T3sl4co1l Super Contributor Posts: What purpose does it irfp360 datasheet BloodyCactus Frequent Contributor Posts: The average current will increase because of the old “area under the curve. I’m assuming you’re switching a DC light here.

I made a test irfp360 datasheet like the img attached without c1 it was very unstable. Did you miss your activation email? Nothing is quite like a great humming power-station.

You can use faster opto coupler like 6N What significance dataheet the frequency? In a circuit like this with a weak pull-down and an incredibly massive irfp360 datasheet chargeirfp360 datasheet be lucky to succeed at 1kHz. I dafasheet using the pwm from the atmega, the default hz is too small I would like irfp360 datasheet or hz I was thinking the optocoupler cannot handle the switching and consider using a 6n is the 4n25 suited for this application or should I use something else?

Check the pic again, He’s using 8. Psi Super Contributor Posts: The flickering is probably the result of the PWM signal beeing modulated by the mains frequency.

The 10K resistor is too high, make it 1K or irfp360 datasheet. A room-sized installation will definitely be a source of EMI!